Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
Just how do you really feel about Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and also often, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is readily easily accessible, the task can move easily; if you have to open up a wall to eliminate the old tub and also place the brand-new bathtub, the job is much harder. In either case, the project is within a house handyman's skills, although you will need a helper to vacate the old tub and also embeded in the new one. Make sure you have actually qualified yourself for the job as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is better to think about utilizing one before you start. Chances are you may need a specialist plumber to make tube links.
This write-up will assist you install a brand-new bath tub in your bathroom if you have already purchased a new tub and do not require to change the setup of your previous water system pipes.
Your devices and also material list should comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is separate the water system. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly troublesome as a result of the limited access that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing the two wood boards under its feet, position the tub in the required setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To install faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression join; then do the exact same for the other tap.
Activate the supply of water as well as examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait until the tub has been made use of a minimum of when as this will certainly resolve it right into its last placement.
Getting ready for the Installment
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, creating the water to permeate the wall between the bathroom and also the tiling, leading to complications with wetness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealer can split rather early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that editorial on How to Install a Bathtub from an acquaintance on our other web blog. Do you know about anybody else who is fascinated by the topic? Please feel free to share it. I treasure reading our article about Tools You Need to Install a New Bathtub .
Call Us Now Report this page